Firefly开源社区

标题: 3568工业核心板无法正常启动 [打印本页]

作者: 大葱科技 时间: 2022-9-19 14:39
标题: 3568工业核心板无法正常启动
3568的底板是我们根据官方文件自己设计的。
目前串口有打印,usb otg口正常烧录, 固件使用最近同步过的代码编译, 没有做任何更改. 现象是开机启动失败, 附件是串口日志
相同的固件在官方AIO-3568J开发板上正常启动
tchip_askquestions

serial_start1.zip

6.75 KB, 下载次数: 2, 下载积分: 灯泡 -1 , 经验 -1

作者: 大葱科技 时间: 2022-9-19 14:56
uboot 打印信息:
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: pmu v1 is valid
INFO: dfs DDR fsp_param[0].freq_mhz= 1560MHz
INFO: dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO: dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO: dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 0
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
I/TC:
I/TC: OP-TEE version: 3.13.0-641-g4167319d3 #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #8 Wed Mar 16 15:14:56 CST 2022 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9

U-Boot 2017.09(u-boot commit id: fc354ea827411c1cc35ddf76162aed02f7a9c7d5)(sdk version: rk356x_linux_release_20220516_v1.2.4a.xml)-gfc354ea827-dirty #dacong (Sep 19 2022 - 13:14:15 +0800)

Model: Firefly RK3568 Board
PreSerial: 2, raw, 0xfe660000
DRAM:  1006 MiB
Sysmem: init
Relocation Offset: 3d32e000
Relocation fdt: 3b9f8b00 - 3b9fecd8
CR: M/C/I
Using default environment

dwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
DM: v1
boot mode: recovery (misc)
FIT: no signed, no conf required
=================begin===================
133713 bytes read in 7 ms (18.2 MiB/s)
DTB(Distro): rk-kernel.dtb
I2c0 speed: 100000Hz
PMIC:  RK8090 (on=0x40, off=0x00)
vdd_logic init 900000 uV
vdd_gpu init 900000 uV
vdd_npu init 900000 uV
io-domain: OK
Could not find baseparameter partition
Model: AIO-3568J HDMI (Linux)
Rockchip UBOOT DRM driver version: v1.0.1
VOP have 1 active VP
vp0 have layer nr:6[0 2 4 1 3 5 ], primary plane: 4
vp1 have layer nr:0[], primary plane: 0
vp2 have layer nr:0[], primary plane: 0
hdmi@fe0a0000 disconnected
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
  apll 816000 KHz
  dpll 780000 KHz
  gpll 1188000 KHz
  cpll 1000000 KHz
  npll 1200000 KHz
  vpll 24000 KHz
  hpll 24000 KHz
  ppll 200000 KHz
  armclk 816000 KHz
  aclk_bus 150000 KHz
  pclk_bus 100000 KHz
  aclk_top_high 500000 KHz
  aclk_top_low 400000 KHz
  hclk_top 150000 KHz
  pclk_top 100000 KHz
  aclk_perimid 300000 KHz
  hclk_perimid 150000 KHz
  pclk_pmu 100000 KHz
Net: eth1: ethernet@fe010000, eth0: ethernet@fe2a0000
Hit key to stop autoboot('CTRL+C'):  0

作者: dengkx 时间: 2022-9-19 15:01
3568q适配的底板是itx-3568q，请使用itx-3568q-ubuntu.mk

作者: 大葱科技 时间: 2022-9-19 15:28

dengkx 发表于 2022-9-19 15:01
3568q适配的底板是itx-3568q，请使用itx-3568q-ubuntu.mk

3568J是工业级，是不是跟商业级的在调试时有什么不同？

作者: dengkx 时间: 2022-9-19 17:42

大葱科技发表于 2022-9-19 15:28
3568J是工业级，是不是跟商业级的在调试时有什么不同？

3568q才是工业级的

欢迎光临 Firefly开源社区 (https://dev.t-firefly.com/)