Firefly开源社区

标题: 我的RK3288板子,烧写任何镜像都是反复重启。求解 [打印本页]

作者: kunyang_yt    时间: 2017-5-3 22:58
标题: 我的RK3288板子,烧写任何镜像都是反复重启。求解
我自己编译的内核和ubuntu系统反复重启。我不装界面系统不会重启。后来我测试我装了network-manager后也会反复重启。无奈我下载官网的也是反复重启。
求解答,应该如何解决。
作者: zhansb    时间: 2017-5-4 09:15
可以把完整的内核log用附件附上来
作者: kunyang_yt    时间: 2017-5-4 15:29
本帖最后由 kunyang_yt 于 2017-5-4 15:32 编辑
zhansb 发表于 2017-5-4 09:15
可以把完整的内核log用附件附上来

DDR Version 1.00 20141007
In
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Memory OK
Memory OK
OUT


U-Boot 2014.10-RK3288-01 (Jan 21 2015 - 16:36:44)

CPU: rk3288
CPU's clock information:
    arm pll = 600000000HZ
    periph pll = 297000000HZ
    ddr pll = 200000000HZ
    codec pll = 384000000HZ
Board:    Rockchip platform Board
DRAM:  Found dram banks:1
Adding bank:0000000000000000(0000000080000000)
128 MiB
storage init OK!
Using default environment

GetParam
check parameter success
Unknow param: MACHINE_MODEL:rk3288!
Unknow param: MACHINE_ID:007!
Unknow param: MANUFACTURER:RK3288!
Unknow param: PWR_HLD: 0,0,A,0,1!
no adc node
can't find dts node for led
can't find dts node for ricoh619
pmic:act8846
Can't find dts node for fuel guage cw201x
SecureBootEn = 0, SecureBootLock = 0

#Boot ver: 2015-01-21#2.19
empty serial no.
checkKey
vbus = 1
no fuel gauge found
no fuel gauge found
read logo_on switch from dts [0]
no fuel gauge found
failed to find part:misc
misc partition not found!
Hit any key to stop autoboot:  1  0
kernel   @ 0x02000000 (0x004f9040)
ramdisk  @ 0x04bf0000 (0x00299a2c)
Secure Boot state: 0
bootrk: do_bootm_linux...
   Loading Device Tree to 0481e000, end 0482a9f2 ... OK
Add bank:0000000000000000, 0000000080000000

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x500
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.14.0 (wanghh@tchipserver2) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #129 SMP Mon Jun 6 15:15:00 CST 2016
[    0.000000] CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Firefly rk3288
[    0.000000] rockchip_ion_reserve
[    0.000000] ion heap(drm): base(0) size(0) align(0)
[    0.000000] ion heap(cma): base(0) size(28000000) align(0)
[    0.000000] ion heap(vmalloc): base(0) size(0) align(0)
[    0.000000] ion_reserve: dma_declare_contiguous failed -38
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] Boot mode: RAMFS (10) flag:  (0x5242c30c)
[    0.000000] PERCPU: Embedded 9 pages/cpu @ee7af000 s14144 r8192 d14528 u36864
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 522768
[    0.000000] Kernel command line: earlyprintk=ttyS2,115200 console=tty0 console=ttyS2,115200 androidboot.selinux=permissive androidboot.hardware=rk30board androidboot.console=ttyS2 root=/dev/block/mtd/by-name/linuxroot linuxroot rw rootfstype=ext4 init=/sbin/init  mtdparts=rk29xxnand:0x00010000@0x00002000(boot),0x00002000@0x00012000(backup),-@0x00014000(linuxroot) storagemedia=emmc loader.timestamp=2015-01-21_16:36:44
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 2063600K/2097152K available (8830K kernel code, 424K rwdata, 2224K rodata, 501K init, 631K bss, 33552K reserved, 1318912K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0bcb9fc   (12047 kB)
[    0.000000]       .init : 0xc0c00000 - 0xc0c7d740   ( 502 kB)
[    0.000000]       .data : 0xc0d00000 - 0xc0d6a028   ( 425 kB)
[    0.000000]        .bss : 0xc0d6a028 - 0xc0e08000   ( 632 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000008] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[    0.000021] Switching to timer-based delay loop
[    0.001705] Console: colour dummy device 80x30
[    0.002816] console [tty0] enabled
[    0.002872] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.002933] pid_max: default: 32768 minimum: 301
[    0.003144] Security Framework initialized
[    0.003181] Yama: becoming mindful.
[    0.003283] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.003326] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.018480] Initializing cgroup subsys devices
[    0.018526] Initializing cgroup subsys freezer
[    0.018595] CPU: Testing write buffer coherency: ok
[    0.018673] ftrace: allocating 27728 entries in 82 pages
[    0.073891] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500
[    0.074176] Setting up static identity map for 0x844608 - 0x8446c0
[    0.077221] CPU1: Booted secondary processor
[    0.077261] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501
[    0.079080] CPU2: Booted secondary processor
[    0.079110] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502
[    0.080939] CPU3: Booted secondary processor
[    0.080969] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503
[    0.081105] Brought up 4 CPUs
[    0.081207] SMP: Total of 4 processors activated.
[    0.081225] CPU: All CPU(s) started in SVC mode.
[    0.082006] devtmpfs: initialized
[    0.088755] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0
[    0.090190] pinctrl core: initialized pinctrl subsystem
[    0.090639] regulator-dummy: no parameters
[    0.090960] NET: Registered protocol family 16
[    0.091726] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.092323] cpuidle: using governor ladder
[    0.092346] cpuidle: using governor menu
[    0.109559] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.109596] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.109681] Switched to clocksource arch_sys_counter
[    0.119699] bio: create slab <bio-0> at 0
[    0.120558] vccsys: no parameters
[    0.120855] vcc33_io: no parameters
[    0.120914] reg-fixed-voltage vcc33-io.15: Failed to find supply vin
[    0.121043] reg-fixed-voltage vcc33-io.15: Failed to register regulator: -517
[    0.121081] platform vcc33-io.15: Driver reg-fixed-voltage requests probe deferral
[    0.121320] vcc_5v: 5000 mV
[    0.121398] vcc_5v: supplied by vccsys
[    0.121823] vcc5_host1: no parameters
[    0.122227] sata_pwr: no parameters
[    0.122645] vcc5_host2: no parameters
[    0.123033] wifi_regulator: no parameters
[    0.123719] SCSI subsystem initialized
[    0.124027] usbcore: registered new interface driver usbfs
[    0.124112] usbcore: registered new interface driver hub
[    0.124270] usbcore: registered new device driver usb
[    0.124467] Linux video capture interface: v2.00
[    0.124547] pps_core: LinuxPPS API ver. 1 registered
[    0.124567] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.124621] PTP clock support registered
[    0.125316] ion_drm_heap_create: 0@0
[    0.125515] Rockchip ion module is successfully loaded (v1.1)
[    0.125887] platform ff9a0000.vpu_service: of_parse_phandle_with_args(/vpu_service@ff9a0000) => -2
[    0.126761] Advanced Linux Sound Architecture Driver Initialized.
[    0.127433] Bluetooth: Core ver 2.20
[    0.127492] NET: Registered protocol family 31
[    0.127512] Bluetooth: HCI device and connection manager initialized
[    0.127543] Bluetooth: HCI socket layer initialized
[    0.127568] Bluetooth: L2CAP socket layer initialized
[    0.127619] Bluetooth: SCO socket layer initialized
[    0.128067] cfg80211: Calling CRDA to update world regulatory domain
[    0.129609] Could not create debugfs 'set_ftrace_filter' entry
[    0.129639] Could not create debugfs 'set_ftrace_notrace' entry
[    0.176436] NET: Registered protocol family 2
[    0.177088] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.177206] TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
[    0.177652] TCP: Hash tables configured (established 8192 bind 8192)
[    0.177746] TCP: reno registered
[    0.177778] UDP hash table entries: 512 (order: 2, 24576 bytes)
[    0.177847] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes)
[    0.178205] NET: Registered protocol family 1
[    0.178501] Unpacking initramfs...
[    0.375551] Freeing initrd memory: 2660K (c4bf0000 - c4e89000)
[    0.376207] hw perfevents: enabled with ARMv7 Cortex-A12 PMU driver, 7 counters available
[    0.377059] probe device ff9a0000.vpu_service
[    0.377418] ff9a0000.vpu_service: power on
[    0.377504] reg_base f0056000
[    0.377525] probe device ff9a0000.vpu_service
[    0.377555] checking hw id 4831
[    0.378128] vpu_service: power off...
[    0.378179] done
[    0.378200] init success
[    0.379572] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.380921] bounce pool size: 64 pages
[    0.391046] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.392328] NTFS driver 2.1.30 [Flags: R/W].
[    0.392739] fuse init (API version 7.22)
[    0.393348] msgmni has been set to 1459
[    0.395002] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.395037] io scheduler noop registered
[    0.395056] io scheduler deadline registered
[    0.395429] io scheduler cfq registered (default)
[    0.397280] backlight.10 supply power not found, using dummy regulator
[    0.400469] dma-pl330 ff250000.dma-controller: Loaded driver for PL330 DMAC-2364208
[    0.400509] dma-pl330 ff250000.dma-controller:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[    0.401453] dma-pl330 ffb20000.dma-controller: Loaded driver for PL330 DMAC-2364208
[    0.401490] dma-pl330 ffb20000.dma-controller:     DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10
[    0.401952] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.403905] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 87, base_baud = 1500000) is a 16550A
[    0.404737] ff190000.serial: ttyS1 at MMIO 0xff190000 (irq = 88, base_baud = 1500000) is a 16550A
[    0.405561] ff690000.serial: ttyS2 at MMIO 0xff690000 (irq = 89, base_baud = 1500000) is a 16550A
[    1.220764] console [ttyS2] enabled
[    1.225055] ff1b0000.serial: ttyS3 at MMIO 0xff1b0000 (irq = 90, base_baud = 1500000) is a 16550A
[    1.235345] [drm] Initialized drm 1.1.0 20060810
[    1.240444] rockchip-lvds ff96c000.lvds: Failed to get supply 'avdd1v0': -517
[    1.247639] platform ff96c000.lvds: Driver rockchip-lvds requests probe deferral
[    1.256216] usbcore: registered new interface driver udl
[    1.262064] panel.11 supply power not found, using dummy regulator
[    1.268479] platform panel.11: Driver panel-simple requests probe deferral
[    1.276139] platform vga-encoder.23: Driver vga-encoder requests probe deferral
[    1.284019] platform vga-connector.24: Driver vga-connector requests probe deferral
[    1.296869] loop: module loaded
[    1.300076] lkdtm: No crash points registered, enable through debugfs
[    1.307286] tun: Universal TUN/TAP device driver, 1.6
[    1.312372] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.319511] stmmaceth ff290000.ethernet: phy regulator is not available yet, deferred probing
[    1.328191] platform ff290000.ethernet: Driver stmmaceth requests probe deferral
[    1.335872] PPP generic driver version 2.4.2
[    1.340401] PPP BSD Compression module registered
[    1.345116] PPP Deflate Compression module registered
[    1.350208] PPP MPPE Compression module registered
[    1.355009] NET: Registered protocol family 24
[    1.359494] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[    1.369172] CSLIP: code copyright 1989 Regents of the University of California.
[    1.376634] Broadcom 43xx driver loaded [ Features: LS ]
[    1.382442] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.388982] ehci-platform: EHCI generic platform driver
[    1.394392] platform ff500000.usb: Driver ehci-platform requests probe deferral
[    1.401975] usbcore: registered new interface driver cdc_acm
[    1.407644] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.415753] usbcore: registered new interface driver usb-storage
[    1.421920] usbcore: registered new interface driver usbserial
[    1.427807] usbcore: registered new interface driver usbserial_generic
[    1.434404] usbserial: USB Serial support registered for generic
[    1.441349] rk3x-i2c ff140000.i2c: using default SCL frequency: 100000
[    1.992919] dwc2 ff540000.usb: DWC OTG Controller
[    1.997931] dwc2 ff540000.usb: new USB bus registered, assigned bus number 1
[    2.005064] dwc2 ff540000.usb: irq 57, io mem 0x00000000
[    2.010694] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.017498] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.024748] usb usb1: Product: DWC OTG Controller
[    2.029463] usb usb1: Manufacturer: Linux 3.14.0 dwc2_hsotg
[    2.035072] usb usb1: SerialNumber: ff540000.usb
[    2.040443] hub 1-0:1.0: USB hub found
[    2.044243] hub 1-0:1.0: 1 port detected
[    2.200582] tpm_i2c_infineon 1-0020: could not request locality
[    2.229968] rk3x-i2c ff140000.i2c: Initialized RK3xxx I2C bus at f0074000
[    2.236919] rk3x-i2c ff150000.i2c: using default SCL frequency: 100000
[    2.243790] rk3x-i2c ff150000.i2c: Initialized RK3xxx I2C bus at f007e000
[    2.250811] rk3x-i2c ff160000.i2c: using default SCL frequency: 100000
[    2.257574] rk3x-i2c ff160000.i2c: Initialized RK3xxx I2C bus at f0092000
[    2.264605] rk3x-i2c ff170000.i2c: using default SCL frequency: 100000
[    2.271382] rk3x-i2c ff170000.i2c: Initialized RK3xxx I2C bus at f0094000
[    2.284592] vdd_arm: 712 <--> 1500 mV at 1000 mV
[    2.295505] vdd_gpu: 712 <--> 1500 mV at 1000 mV
[    2.304410] act8846_i2c_probe,line=898
[    2.309168] act8846_parse_dt,line=746
[    2.313348] act8846_i2c_probe: act8846_pmic_hold=1
[    2.318169] act8846_i2c_probe: act8846_pmic_sleep=1
[    2.323092] act8846_i2c_probe: act8846_pmic_cpu_det_gpio=1
[    2.328600] act8846_i2c_probe: act8846_pmic_usb_hub_reset_gpio=1
[    2.336526] vcc_sys: 1200 mV
[    2.341710] vcc_io: 3300 mV
[    2.345936] vdd_logic: 700 <--> 1500 mV at 1100 mV
[    2.353122] act_dcdc4: 2000 mV
[    2.358464] vccio_sd: 3300 mV
[    2.363750] vdd10_lcd: 1050 mV
[    2.369077] afvdd_28: 1800 mV
[    2.374390] vcca_33: 3300 mV
[    2.379544] vcc_lan: 3300 mV
[    2.384748] vdd_10: 1100 mV
[    2.389844] vcc_18: 1800 mV
[    2.394915] vcc18_lcd: 1850 mV
[    2.398412] rk3x-i2c ff650000.i2c: Initialized RK3xxx I2C bus at f0096000
[    2.409716] rk3x-i2c ff660000.i2c: Initialized RK3xxx I2C bus at f0098000
[    2.416838] lirc_dev: IR Remote Control driver registered, major 245
[    2.423332] IR NEC protocol handler initialized
[    2.427871] IR RC5(x) protocol handler initialized
[    2.429758] usb 1-1: new high-speed USB device number 2 using dwc2
[    2.438871] IR RC6 protocol handler initialized
[    2.443432] IR JVC protocol handler initialized
[    2.447969] IR Sony protocol handler initialized
[    2.452605] IR RC5 (streamzap) protocol handler initialized
[    2.458183] IR SANYO protocol handler initialized
[    2.462906] IR Sharp protocol handler initialized
[    2.467616] IR MCE Keyboard/mouse protocol handler initialized
[    2.473466] IR LIRC bridge handler initialized
[    2.478284] Registered IR keymap rc-empty
[    2.482708] input: gpio_ir_recv as /devices/gpio-ir-receiver.13/rc/rc0/input0
[    2.490140] rc0: gpio_ir_recv as /devices/gpio-ir-receiver.13/rc/rc0
[    2.496935] input: MCE IR Keyboard/Mouse (gpio-rc-recv) as /devices/virtual/input/input1
[    2.505481] rc rc0: lirc_dev: driver ir-lirc-codec (gpio-rc-recv) registered at minor = 0
[    2.514246] usbcore: registered new interface driver uvcvideo
[    2.520039] USB Video Class driver (1.1.1)
[    2.526395] rockchip-thermal ff280000.tsadc: Missing tshut mode property, using default (gpio)
[    2.535057] rockchip-thermal ff280000.tsadc: Missing tshut-polarity property, using default (low)
[    2.545128] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[    2.553835] device-mapper: verity-chromeos: dm-verity-chromeos registered
[    2.560658] device-mapper: bootcache: version 0.1.0 loaded
[    2.567641] sdhci: Secure Digital Host Controller Interface driver
[    2.573861] sdhci: Copyright(c) Pierre Ossman
[    2.578226] Synopsys Designware Multimedia Card Interface Driver
[    2.585039] dwmmc_rockchip ff0d0000.dwmmc: Using internal DMA controller.
[    2.591889] dwmmc_rockchip ff0d0000.dwmmc: Version ID is 270a
[    2.597676] dwmmc_rockchip ff0d0000.dwmmc: DW MMC controller at irq 65, 32 bit host data width, 256 deep fifo
[    2.608748] ERROR: could not get clock /dwmmc@ff0d0000:card_ext_clock(2)
[    2.615550] wifi_regulator: could not add device link mmc2 err -2
[    2.629923] usb 1-1: New USB device found, idVendor=1a40, idProduct=0101
[    2.636618] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    2.643756] usb 1-1: Product: USB 2.0 Hub [MTT]
[    2.648601] hub 1-1:1.0: USB hub found
[    2.652399] hub 1-1:1.0: 4 ports detected
[    2.699710] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    2.719710] dwmmc_rockchip ff0d0000.dwmmc: 1 slots initialized
[    2.725894] dwmmc_rockchip ff0f0000.dwmmc: Using internal DMA controller.
[    2.732705] dwmmc_rockchip ff0f0000.dwmmc: Version ID is 270a
[    2.738465] dwmmc_rockchip ff0f0000.dwmmc: DW MMC controller at irq 67, 32 bit host data width, 256 deep fifo
[    2.748408] ff0f0000.dwmmc supply vmmc not found, using dummy regulator
[    2.755065] dwmmc_rockchip ff0f0000.dwmmc: Failed getting OCR mask: -22
[    2.761740] mmc0 supply card-external-vcc not found, using dummy regulator
[    2.768624] regulator-dummy: could not add device link mmc0 err -2
[    2.782982] mmc2: queuing unknown CIS tuple 0x80 (2 bytes)
[    2.789978] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[    2.796955] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[    2.805166] mmc2: queuing unknown CIS tuple 0x80 (7 bytes)
[    2.829680] dwmmc_rockchip ff0f0000.dwmmc: could not set regulator OCR (-22)
[    2.836728] dwmmc_rockchip ff0f0000.dwmmc: failed to enable vmmc regulator
[    2.859868] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    2.880030] dwmmc_rockchip ff0f0000.dwmmc: 1 slots initialized
[    2.886786] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.894078] hidraw: raw HID events driver (C) Jiri Kosina
[    2.900223] dwc2 ff580000.usb: DWC OTG Controller
[    2.906175] dwc2 ff580000.usb: new USB bus registered, assigned bus number 2
[    2.906483] usbcore: registered new interface driver usbhid
[    2.906490] usbhid: USB HID core driver
[    2.907173] ashmem: initialized
[    2.908774] rk3288-dmc ff610000.dmc: DDR3 Device
[    2.908795] rk3288-dmc ff610000.dmc: DDR3 Device
[    2.935561] dwc2 ff580000.usb: irq 55, io mem 0x00000000
[    2.938586] ES8323 2-0010: es8323_i2c_probe() Can not read property spk-con-gpio
[    2.948837] ES8323 2-0010: es8323 probe i2c recv ok
[    2.949314] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    2.949342] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.949363] usb usb2: Product: DWC OTG Controller
[    2.949400] usb usb2: Manufacturer: Linux 3.14.0 dwc2_hsotg
[    2.949418] usb usb2: SerialNumber: ff580000.usb
[    2.958867] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    2.969189] mmc2: queuing unknown CIS tuple 0x91 (3 bytes)
[    2.969278] mmc2: new high speed SDIO card at address 0001
[    2.979864] brcmfmac: brcmf_sdio_drivestrengthinit: No SDIO Drive strength init done for chip 4339 rev 2 pmurev 23
[    2.981877] brcmfmac_sdio mmc2:0001:1: Direct firmware load failed with error -2
[    2.981914] brcmfmac_sdio mmc2:0001:1: Falling back to user helper
[    3.022737] mmc0: unrecognised EXT_CSD revision 8
[    3.022762] mmc0: error -22 whilst initialising MMC card
[    3.038328] usb 1-1.1: new full-speed USB device number 3 using dwc2
[    3.039486] hub 2-0:1.0: USB hub found
[    3.039507] hub 2-0:1.0: 1 port detected
[    3.039717] clk: failed to reparent sclk_i2s0 to sclk_i2s0: -22
[    3.039966] rockchip-hdmi-audio hdmi_audio.6: ASoC: CODEC dw-hdmi-audio not registered
[    3.039986] rockchip-hdmi-audio hdmi_audio.6: register card failed (-517)
[    3.039994] platform hdmi_audio.6: Driver rockchip-hdmi-audio requests probe deferral
[    3.040254] ES8323 2-0010: es8323_probe:register ISR (irq=193)
[    3.184461] usb 1-1.1: New USB device found, idVendor=062a, idProduct=4182
[    3.191578] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    3.199024] usb 1-1.1: Product: 2.4G Keyboard Mouse
[    3.204117] usb 1-1.1: Manufacturer: MOSART Semi.
[    3.221570] input: MOSART Semi. 2.4G Keyboard Mouse as /devices/ff540000.usb/usb1/1-1/1-1.1/1-1.1:1.0/0003:062A:4182.0001/input/input2
[    3.235780] hid-generic 0003:062A:4182.0001: input,hidraw0: USB HID v1.10 Keyboard [MOSART Semi. 2.4G Keyboard Mouse] on usb-ff540000.usb-1.1/input0
[    3.256214] input: MOSART Semi. 2.4G Keyboard Mouse as /devices/ff540000.usb/usb1/1-1/1-1.1/1-1.1:1.1/0003:062A:4182.0002/input/input3
[    3.268551] hid-generic 0003:062A:4182.0002: input,hiddev0,hidraw1: USB HID v1.10 Mouse [MOSART Semi. 2.4G Keyboard Mouse] on usb-ff540000.usb-1.1/input1
[    3.641854] random: nonblocking pool is initialized
[    3.716142] rockchip-es8323 sound.22: ES8323 HiFi <-> ff890000.i2s mapping ok
[    3.728628] rockchip-es8323 sound.22: es8323 audio init success.
[    3.734746] u32 classifier
[    3.737449]     Actions configured
[    3.740861] Netfilter messages via NETLINK v0.30.
[    3.745595] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[    3.751946] ctnetlink v0.93: registering with nfnetlink.
[    3.757466] ip_tables: (C) 2000-2006 Netfilter Core Team
[    3.762844] TCP: cubic registered
[    3.766156] Initializing XFRM netlink socket
[    3.770755] NET: Registered protocol family 10
[    3.775718] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    3.781288] sit: IPv6 over IPv4 tunneling driver
[    3.786225] NET: Registered protocol family 17
[    3.790700] NET: Registered protocol family 15
[    3.795182] Bridge firewalling registered
[    3.799201] l2tp_core: L2TP core driver, V2.0
[    3.803565] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[    3.808350] lib80211: common routines for IEEE802.11 drivers
[    3.814574] mali ffa30000.gpu: freq:600000000 Hz volt:1250000 uV
[    3.821746] mali ffa30000.gpu: initial freq = 594000000
[    3.827206] mali ffa30000.gpu: GPU identified as 0x0750 r0p0 status 1
[    3.834014] mali ffa30000.gpu: Probed as mali0
[    3.838683] ThumbEE CPU extension supported.
[    3.842976] Registering SWP/SWPB emulation handler
[    3.848207] regulator-dummy: disabling
[    3.852167] vcc33_io: no parameters
[    3.855679] vcc33_io: supplied by vcc_io
[    3.860842] rockchip-lvds ff96c000.lvds: neither panel nor encoder found
[    3.867647] platform ff96c000.lvds: Driver rockchip-lvds requests probe deferral
[    3.875206] panel.11 supply power not found, using dummy regulator
[    3.881610] platform vga-encoder.23: Driver vga-encoder requests probe deferral
[    3.889548] stmmaceth ff290000.ethernet: rk_gmac_setup: clock input or output? (input).
[    3.897575] stmmaceth ff290000.ethernet: rk_gmac_setup: TX delay(0x30).
[    3.904203] stmmaceth ff290000.ethernet: rk_gmac_setup: RX delay(0x10).
[    3.910833] stmmaceth ff290000.ethernet: rk_gmac_setup: init for RGMII
[    3.917420] stmmaceth ff290000.ethernet: gmac_clk_init: clock input from PHY
[    3.929511] stmmaceth ff290000.ethernet: no reset control found
[    3.935439] stmmac - user ID: 0x10, Synopsys ID: 0x35
[    3.940500]  Ring mode enabled
[    3.943557]  DMA HW capability register supported
[    3.948087]  Normal descriptors
[    3.951427]  RX Checksum Offload Engine supported (type 2)
[    3.956910]  TX Checksum insertion supported
[    3.961185]  Wake-Up On Lan supported
[    3.964875]  Enable RX Mitigation via HW Watchdog Timer
[    4.027625] libphy: stmmac: probed
[    4.031078] eth0: PHY ID 001cc915 at 0 IRQ 0 (stmmac-0:00) active
[    4.037166] eth0: PHY ID 001cc915 at 1 IRQ 0 (stmmac-0:01)
[    4.042990] platform ff500000.usb: Driver ehci-platform requests probe deferral
[    4.050715] rockchip-hdmi-audio hdmi_audio.6: ASoC: CODEC dw-hdmi-audio not registered
[    4.058687] rockchip-hdmi-audio hdmi_audio.6: register card failed (-517)
[    4.065536] platform hdmi_audio.6: Driver rockchip-hdmi-audio requests probe deferral
[    4.075994] rockchip-lvds ff96c000.lvds: neither panel nor encoder found
[    4.082786] platform ff96c000.lvds: Driver rockchip-lvds requests probe deferral
[    4.090404] platform ff500000.usb: Driver ehci-platform requests probe deferral
[    4.097796] rockchip-hdmi-audio hdmi_audio.6: ASoC: CODEC dw-hdmi-audio not registered
[    4.105720] rockchip-hdmi-audio hdmi_audio.6: register card failed (-517)
[    4.112509] platform hdmi_audio.6: Driver rockchip-hdmi-audio requests probe deferral
[    4.121891] rockchip-drm display-subsystem.4: bound ff940000.vop (ops vop_component_ops)
[    4.130176] rockchip-drm display-subsystem.4: bound ff930000.vop (ops vop_component_ops)
[    4.138353] dwhdmi-rockchip ff980000.hdmi: Detected HDMI controller 0x20:0xa:0xa0:0xc1
[    4.146278] dwhdmi-rockchip ff980000.hdmi: Detected HDMI config_id 0xbf:0x22:0xc2:0x0
[    4.154382] dw-hdmi-audio dw-hdmi-audio: hdmi audio init success.
[    4.160490] rockchip-drm display-subsystem.4: bound ff980000.hdmi (ops dw_hdmi_rockchip_ops)
[    4.168978] vga-encoder vga-encoder.23: bound vga-connector.24 (ops vga_connector_ops)
[    4.172531] dwhdmi-rockchip ff980000.hdmi: monitor does not support audio
[    4.183675] rockchip-lvds ff96c000.lvds: bound vga-encoder.23 (ops vga_encoder_ops)
[    4.191344] rockchip-drm display-subsystem.4: bound ff96c000.lvds (ops rockchip_lvds_component_ops)
[    4.200504] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    4.207101] [drm] No driver support for vblank timestamp query.
[    4.261876] rockchip-vop ff940000.vop: Attached to iommu domain
[    4.299616] rockchip-vop ff930000.vop: Attached to iommu domain
[    4.299644] rk3288-dmc ff610000.dmc: suspending DVFS and going to max freq
[    4.324471] Console: switching to colour frame buffer device 240x67
[    4.360726] rockchip-drm display-subsystem.4: fb0:  frame buffer device
[    4.367385] rockchip-drm display-subsystem.4: registered panic notifier
[    4.374051] rockchip-drm display-subsystem.4: rk drm load success
[    4.380374] platform ff500000.usb: Driver ehci-platform requests probe deferral
[    4.387884] dw-hdmi-audio dw-hdmi-audio: jack report [4]
[    4.394126] rockchip-hdmi-audio hdmi_audio.6: dw-hdmi-hifi <-> ff890000.i2s mapping ok
[    4.402383] input: RockchipHDMI HDMI Jack as /devices/hdmi_audio.6/sound/card1/input4
[    4.410443] rockchip-hdmi-audio hdmi_audio.6: hdmi audio init success.
[    4.417107] platform ff500000.usb: Driver ehci-platform requests probe deferral
[    4.424742] platform ff500000.usb: Driver ehci-pDDR Version 1.00 20141007
In
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Memory OK

Memory OK
OUT


U-Boot 2014.10-RK3288-01 (Jan 21 2015 - 16:36:44)

CPU: rk3288
CPU's clock information:
    arm pll = 600000000HZ
    periph pll = 297000000HZ
    ddr pll = 200000000HZ
    codec pll = 384000000HZ
Board:    Rockchip platform Board
DRAM:  Found dram banks:1
Adding bank:0000000000000000(0000000080000000)
128 MiB
storage init OK!
Using default environment

GetParam
check parameter success
Unknow param: MACHINE_MODEL:rk3288!
Unknow param: MACHINE_ID:007!
Unknow param: MANUFACTURER:RK3288!
Unknow param: PWR_HLD: 0,0,A,0,1!
no adc node
can't find dts node for led
can't find dts node for ricoh619
pmic:act8846
Can't find dts node for fuel guage cw201x
SecureBootEn = 0, SecureBootLock = 0

#Boot ver: 2015-01-21#2.19
empty serial no.
checkKey
vbus = 1
no fuel gauge found
no fuel gauge found
read logo_on switch from dts [0]
no fuel gauge found
failed to find part:misc
misc partition not found!
Hit any key to stop autoboot:  1  0
kernel   @ 0x02000000 (0x004f9040)
ramdisk  @ 0x04bf0000 (0x00299a2c)
Secure Boot state: 0
bootrk: do_bootm_linux...
   Loading Device Tree to 0481e000, end 0482a9f2 ... OK
Add bank:0000000000000000, 0000000080000000

Starting kernel ...


我使用的这个镜像是Firefly-rk3288_Ubuntu_1404_2016_6171712_Beta.img
我使用了很多镜像都是反复重启.
板子是Firefly-rk3288 2GB/16GB  2016-12-26

作者: jjffgg    时间: 2017-6-3 17:35
我的供电不足就会这样, 换城5v 2A INPUT




欢迎光临 Firefly开源社区 (https://dev.t-firefly.com/) Powered by Discuz! X3.1